STUDI NUMERIK: KOMPARASI PENGARUH RASIO PANJANG DAN DIAMETER GUIDE VANE TERHADAP ALIRAN UDARA OUTLET DUCTING
Abstract
Guide vane has an important role for conditioning flow pattern of fluid velocity. With the configuration of axial turbine blade, the flow pattern near wall must have the highest velocity. As such that intention, this research is conducted to compare between the effect of dimension ratio of length and diameter of guide vane using ANSYS FLUENT 17. The dimension ratio of guide vane has been divided into two types with each of types has three variations. Type 1 is ratio of length that having variation A, B and C, whilst type 2 is ratio of diameter with D, E and F variations. The result shows that variation B and F produces the highest velocity. Because the effect of acceleration on variation B is maximum so that it increases the velocity, while on variation F has the smallest angle of guide vane that would reduce the drag force.
Downloads
References
A. Annuk et al., “Increasing self electricity consumption by using double water heating tanks for residential net zeroenergy buildings,†2017 6th Int. Conf. Renew. Energy Res. Appl. ICRERA 2017, vol. 2017-Janua, pp. 106–110, 2017, doi: 10.1109/ICRERA.2017.8191249.
K. V. Alexander, E. P. Giddens, and A. M. Fuller, “Axial-flow turbines for low head microhydro systems,†Renew. Energy, vol. 34, no. 1, pp. 35–47, 2009, doi: 10.1016/j.renene.2008.03.017.
R. Alonso, M. Jackson, P. Santoro, M. Fossati, S. Solari, and L. Teixeira, “Wave and tidal energy resource assessment in Uruguayan shelf seas,†Renew. Energy, vol. 114, pp. 18–31, 2017, doi: 10.1016/j.renene.2017.03.074.
P. R. Ansyah, J. Waluyo, Suhanan, M. Najib, and F. Anggara, “Thermal behavior of melting paraffin wax process in cylindrical capsule by experimental study,†vol. 020008, p. 020008, 2018, doi: 10.1063/1.5049968.
F. Anggara, H. Carles, P.R. Ansyah, “Studi Numerik: Pengaruh Debit Inlet Terhadap Karakteristik Pelelehan Paraffin Wax Pada Tabung Silinder,†Sci. J. Mech. Eng. Kinemat.,vol. 4, no. 1, pp. 1–8, 2019.
S. Chitrakar, H. P. Neopane, and O. G. Dahlhaug, “Development of a test rig for investigating the flow field around guide vanes of Francis turbines,†Flow Meas. Instrum., vol. 70, p. 101648, 2019, doi: 10.1016/j.flowmeasinst.2019.101648.
X. Wang et al., “Grey relational analysis and optimization of guide vane for reactor coolant pump in the coasting transient process,†Ann. Nucl. Energy, vol. 133, pp. 431–440, 2019, doi: 10.1016/j.anucene.2019.05.015.
R.A Ratu, F.Anggara, “Investigasi Analisis Numerik Pada Pengaruh Perbandingan Diameter Inlet Dan Outlet Guide Vane Terhadap Velocity Profile,†Sci. J. Mech. Eng. Kinemat., vol. 5, no. 1, pp. 1–10, 2020, doi: 10.20527/sjmekinematika.v5i1.98.
A. Aryadillah and A. Mursadin, “Analisis Perbandingan Kinerja Sistem Distribusi Panas Pada Variasi Ruang Mesin Pengering Ikan,†Sci. J. Mech. Eng. Kinemat., vol. 1, no. 1, pp. 27–36, 2016, doi: 10.20527/sjmekinematika.v1i1.25.
F. Anggara et al., “Simulation and validation of PCM melting in concentric double pipe heat exchanger,†AIP Conf. Proc., vol. 2001, 2018, doi: 10.1063/1.5049967.
Y. ting LIU, T. zu YANG, Z. CHEN, Z. yu ZHU, L. ZHANG, and Q. HUANG, “Experiment and numerical simulation of two-phase flow in oxygen enriched side-blown furnace,†Trans. Nonferrous Met. Soc. China (English Ed., vol. 30, no. 1, pp. 249–258, 2020, doi: 10.1016/S1003-6326(19)65196-4.
ANSYS, “ANSYS Fluent Theory Guide--Release 17.0,†Comput. Commun., vol. 15317, no. January, pp. 724–746, 2016, doi: 10.1016/0140-3664(87)90311-2.
ANSYS Inc. (US), “Ansys Users’ Guide,†Aging (Albany. NY)., vol. 7, no. 11, pp. 956–963, 2015, doi: 10.1017/CBO9781107415324.004.
E.J. Shaughnessy, I. M. Katz, J.P. Schaffer, 2013, Introduction To Fluid Mechanics :MIT Press
